What does ER if mean on Kenmore Elite refrigerator?

ice fan
The Er If error code indicates that you have a broken ice fan. The ice fan blows air through ducts in the door to cool the ice maker compartment. When the ice fan shorts, it can damage components in your refrigerator’s main electronic control board. You’ll need to replace both parts to resolve the issue.

Why does my Kenmore refrigerator say ER?

This error code Er FF indicates a problem with the evaporator fan motor but it can also be with the main control board. When the power cord is disconnected for 30 seconds and then reconnected, it resets the board. If the motor is still running, the main board, which is located behind the unit, will need to be replaced.

What does ER 1F mean on Kenmore refrigerator?

Er 1f, Er IF, Er 1F, or just 1F, IF, or F1. These error codes are all indicating the same thing (ICE MAKER FAN). With frost and ice accumulating on the evaporator and inside the evaporator compartment, the fan(s) could or would be restricted by the ice and frost in the air tunnels and produce the error code.

Is there a recall on Kenmore Elite refrigerator?

LG Electronics and Sears, Roebuck and Co. are recalling about 20,000 three-door refrigerators sold under the LG and Kenmore Elite Trio names. A faulty component in the condenser fan motor can short circuit. This could cause the condenser fan motor to overheat, posing a potential fire hazard to consumers.

Does Kenmore Elite refrigerator have a reset button?

Sears is the exclusive retailer of Kenmore refrigerators. Open one refrigerator door and press the “Ultra Ice” and “Home” buttons simultaneously for five seconds to turn off the refrigerator’s controls. Unplug the refrigerator’s power cord from the wall outlet.

How do I run diagnostics on my Kenmore Elite refrigerator?

Enter the diagnostic mode by pressing and holding the Lock button for 3 seconds, then press and hold the Freezer and Refrigerator buttons while pressing the Acela Ice button 5 times. The digital display will show operating time (number of minutes it’s been plugged in).

How do I test my Kenmore Elite refrigerator?

How do I reset my Kenmore Elite refrigerator?

How to Reset a Sears Refrigerator

  1. Open one refrigerator door and press the “Ultra Ice” and “Home” buttons simultaneously for five seconds to turn off the refrigerator’s controls.
  2. Unplug the refrigerator’s power cord from the wall outlet.
  3. Reconnect the power cord to the wall outlet. The refrigerator is now reset.

How long should a Kenmore Elite refrigerator last?

10 to 20 years
Your Fridge Is More Than 10 Years Old A refrigerator can last anywhere from 10 to 20 years. The older your unit is, the more it may cost to repair it.

Why is my Kenmore Elite refrigerator not getting cold?

Check the condenser coils to determine if they are dirty—if the condenser coils are dirty, clean them. The condenser fan motor draws air though the condenser coils and over the compressor. If the condenser fan motor is not working properly, the refrigerator won’t cool properly.

What is the average life expectancy of a refrigerator?

The average lifespan of a refrigerator According to a study from the National Association of Home Builders and Bank of America (NYSE: BAC), the typical standard fridge lasts 13 years. For compact refrigerators, often called mini fridges, the lifespan is slightly less at nine years.

What is the error code on the Kenmore Elite refrigerator?

Kenmore elite refrigerator error code ER RF. December 6, 2020. Defrost your Kenmore Elite Refrigerator and switch it on again. If the ERRF is still there, check the fan motor. Use the control board or check the motor itself. If you see this error code on your fridge’s control board, the system is viewing the fan motor’s work as improper.

What does the ER stand for on a Kenmore refrigerator?

Kenmore elite refrigerator error code er co This error code stands for ‘communication error’ and occurs due to communication failure between the main control board (on the back panel) and display control board (on the freezer door). This may be due to poor wiring and/or loose connection.

What to do if your Kenmore refrigerator has ERRF?

Defrost your Kenmore Elite Refrigerator and switch it on again. If the ERRF is still there, check the fan motor. Use the control board or check the motor itself.

What does error code ER 1F mean on Kenmore Elite?

Try a Goggle search for question 264983. If the image still does not enlarge let me know and I will try something else. The Er IF error code indicates that the main control board detects that the ice compartment cooling fan is not working. This will cause a lack of cooling in the ice compartment and will normally result in no ice production.